Holography Supplies and Accessories
Laser Diode Holography Kit
Laser Diode Holography Kit includes everything you need to produce first rate holograms. (white light viewable & transmission). Kit includes: 5 mW diode laser, radius mirror, 18 sqr. 1/8 thick steel table top, inner tube, film holder, (2) holographic film plates, JD-2 Developing Kit, developing trays, tongs, gloves, safelight, sea shell model, 4 sorbathane pads, shutter card, white card, glass.
LD-KIT - $395.00
Holography Kit
Diode Laser
Diode Laser 650 nanometers 5 milliwatts suitable for shooting holograms. Includes power supply. Estimate lifetime 20,000 hours.
DLAS-05 - $74.95
Diode Laser
Laser Diode Holography Booklet
Helium Neon Laser
Helium Neon Laser (surplus)
0.5 Milliwatts power output, 632 nanometers, TEM00 mode
(Requires 12 VDC @ 1 amp Power supply - not included)
LAS-01 - $120.00
Helium Neon Laser
Laser Tube
Laser Diode Power Supply
The laser driver kit can supply regulated current to any laser diode that requires a current up to 3A, It will power almost any laser diode from the lowest range 35mA Blu-ray laser, up to a multi-amp green laser.
- This kit is only a regulator and NOT a fully working laser system.
- This kit is only intended to be part of a laser diode system for holography or light show for entertainment purposes.
- You cannot use this kit to build a device that is against the law
Kit Includes:
- Schematics
- Instructions for assembly, testing and calibration
- Printed circuit board (PCB)
- All semiconductors
- All capacitors
- All resistors except the two larger resistor in front. You must determine yourself experimentally the one(s) appropriate for your diode requirements. This is explained in the documentation.
- Test points to measure and monitor current through laser diode while in operation.
Laser Diode (not included) Close Up
LDD-01 $34.95 (Kit Requires Assembly)
Laser Power Supply
Helium Neon Laser with Power Supply
Surplus HeNe Laser with Power Supply
LAS-04 - $99.95
Surplus HeNe Laser with Power Supply
Holographic Glass Plates
2 pcs Holographic Film Glass Plates, 2.5" x 2.5"
FL-02 - $18.00
Holographic Film Glass Plates
Film Holder
Film Holder (for acetate film & glass plate)
Consists of two 3.5" transparent square plastic plates, two metal binding clips and two bar magnets. Used to support acetate film on metal table. Binding clips and magnets may be used without the transparent plastic to hold holographic glass plates on metal table.
FH-01 - $10.00
Film Holder
Safe Light
Safe Light
Green Electroluminesent Light. For use with red sensitive film.
SL-01 - $45.00
Safe Light
Developing Trays
Developing Trays
Small plastic trays suitable for developing chemistry and holographic film listed above. Stipled bottom prevents film from sticking to bottom of tray.
TR-01 - $5.00
Development Trays
Tongs
Film Developing Tongs
Wood tongs for developing holographic film listed above. Use tongs to move film in chemistry trays.
Tongs - $2.00
Tongs
Spreading Optics
Radius Mirror
Ball Lens
DCV Lens
DCV Lens -- 6 mm Diameter Focal Length -6 mm Double-Concave (DCV) Lenses have two inward curved surfaces and a negative focal length. They are used for image reduction and to spread light.
DCV-01 - $34.95
DCV Lens
Spherical Mirror
Front Surface Mirrors (FSM)
FS-01 5/8" x 3/4" Front Surface Mirror
FS-02 3" x 3" Front Surface Mirror
FS-03 6" x 7" Front Surface Mirror
FS-01 - $4.00
5/8" x 3/4" Front Surface Mirror
FS-02 - $8.00
3" x 3" Front Surface Mirror
FS-03 - $12.00
6" x 7" Front Surface Mirror
Beam Splitters
BS-01 1:1 Ratio Beam Splitter
BS-02 2:1 Ratio Beam Splitter
BS-03 3:1 Ratio Beam Splitter
BS-01 - $19.95
1:1 Ratio Beam Splitter
BS-02 - $19.95
2:1 Ratio Beam Splitter
BS-03 - $19.95
3:1 Ratio Beam Splitter
Magnets
Rectangular Magnet
1" x 1"x .5"Bar Magnet
3/8" x 3/8" x 1"Miscellanious Supplies
Steel Plate
Steel Plate 1" x 5" x 1/16" thk, show with square magnet at base. Magnet not included. Steel plate is used to secure magnetically mounted optical components on steel holographic isolation table.
STL-01 - $1.50
Steel Plate
Isolation Table
Isolation Table
Steel Table 24" x 24" x 1/8 thk (2 sheets)
(30 lbs, UPS shipping is additional)
TB-01 - $70.00
Isolation Table
Small Inner Tube
Sorbathane Pads
Tungsten Halogen Lamp
Tungsten Halogen Lamp
point light source for displaying reflection holograms 75 watts. Edison base.
TGH-01 - $12.00
Tungsten Halogen Lamp
Holography Film Processing Kit
Holography Film Processing Kit:
This formula is excellent for both reflection and transmission holgrams. The solution has a tray life of one day. Processes 20 4"x5" plates.
JD-2 - $30.50
Holography Film Processing Kit
